• MATCH
  • MISMATCH
  • NETWORK
  • HUMAN

How to verify IP address membership with your AI

Connect the IP Subnet Calculator to your AI client once. From then on, your agent handles the subnet math for you.

Ask AI about this page

Short answer

Can my AI check if an IP is in a subnet?

Yes. Your agent uses the calculate_ip_subnet tool to perform the binary math needed to confirm membership. You get a direct answer on whether the IP belongs to the specified range.

The results you get.

What your AI delivers.

The AI processes your network data and provides these specific outcomes.

MATCH

Membership confirmed

The AI confirms the IP is inside the subnet. You get a clear yes or no based on the math.

MISMATCH

Out of range

The AI determines the IP falls outside the subnet. It identifies the mismatch immediately.

NETWORK

Subnet boundaries

The AI calculates the network and broadcast addresses. This gives you the full scope of the range.

HUMAN

Manual decisions

The AI provides the math, but you decide how to apply it to your firewall or routing tables.

The workflow

What your AI does when the request arrives.

Your agent uses specialized tools to turn raw IP strings into mathematical proofs.

  1. Parse input

    Your agent reads the IP address and the CIDR or subnet mask you provided.

    calculate_ip_subnet

  2. Calculate mask

    The AI applies the subnet mask to the IP to find the network prefix.

    calculate_ip_subnet

  3. Check range

    The tool compares the target IP against the subnet's start and end boundaries.

    calculate_ip_subnet

  4. Confirm status

    The AI returns a final verdict on whether the IP is a member of that subnet.

    calculate_ip_subnet

Try it

Copy these to start.

Paste these lines into your chat to begin.

Starting points

Swap out the IP addresses and subnet masks in these examples for your own data.

IP Subnet Calculator Connector

You're all set. Choose your MCP client and follow the setup instructions.

Connector linkhttps://edge.vinkius.com/vk_preview_29Tf1MOJ3qbGOgwFWVS0KF3OXchOQiZFzidvjwFU/mcp

Claude Desktop

Follow the steps below to connect in seconds.

  1. 1In Claude Desktop, open Settings → Connectors.
  2. 2Click “Add custom connector” and paste the connector link above as the remote MCP server URL.
  3. 3Click Add and start a new chat — IP Subnet Calculator capabilities are ready to use.
Configuration · claude_desktop_config.jsonCopy
{
  "mcpServers": {
    "ip-subnet-calculator-mcp": {
      "url": "https://edge.vinkius.com/vk_preview_29Tf1MOJ3qbGOgwFWVS0KF3OXchOQiZFzidvjwFU/mcp"
    }
  }
}
Copy into chat04

  • Check if 192.168.1.45 is inside the 192.168.1.0/24 subnet.

  • Is 10.0.0.5 part of the 10.0.0.0/8 range?

  • Verify if 172.16.5.10 belongs to the subnet 172.16.0.0 with mask 255.255.0.0.

  • Does 192.168.50.12 fall within 192.168.50.0/24?

  • Claude
  • ChatGPT
  • Cursor
  • VS Code
  • Windsurf
  • Claude Code
  • JetBrains
  • Cline

Start here

Connect IP Subnet Calculator once, then ask.

Connect the MCP to your client with one click. Your credentials stay encrypted on our side, and you can find more details on the Connector page.

Connect IP Subnet Calculator to your AI

FAQ

How this task behaves.

  • 01

    Can the AI change my network configuration?

    No. The AI only performs calculations. It cannot touch your routers, firewalls, or any hardware.

  • 02

    Does the AI scan my network?

    No. The AI only looks at the specific IP addresses you provide in the chat.

  • 03

    Can it handle IPv6 addresses?

    No. This tool is built specifically for IPv4 subnetting.

  • 04

    Will it save my IP data?

    No. The AI processes the math and provides the answer without storing your network details.

  • 05

    Can I use this in Cursor?

    Yes. Any MCP-compatible client like Cursor or Claude Desktop works with this MCP.

  • More questions about IP Subnet Calculator? The Connector page answers them. See everything the IP Subnet Calculator Connector can do

Connect IP Subnet Calculator to Claude, Cursor, ChatGPT & more