• DATA
  • SPATIAL
  • REPORT
  • HUMAN

How to verify indoor geofence boundaries with your AI

Connect Pointr to your agent to audit spatial accuracy. Once connected, your AI can cross-reference digital zones against real building geometry.

Ask AI about this page

Short answer

How do I check if my indoor geofences are accurate?

Your AI pulls the specific polygon coordinates for your trigger zones and compares them to the building's structural layout. This identifies any zones that overlap walls or extend into restricted areas. You'll see exactly where your digital boundaries drift from the physical floor plan.

Audit outcomes

Where discrepancies appear

What happens when your AI runs a spatial audit.

DATA

Polygon extraction

The AI pulls the exact mathematical boundaries for every active zone. You get a clean list of coordinates to review.

SPATIAL

Layout alignment

The agent compares zone shapes against the building's footprint. It flags where a geofence hits a wall or a pillar.

REPORT

Error identification

Your AI highlights specific zones that are logically broken or physically impossible. You receive a list of coordinates that need fixing.

HUMAN

Manual correction

The AI identifies the errors, but you must manually adjust the zones in your management console. The agent cannot move the boundaries for you.

The workflow

What your AI does when the audit starts.

The AI handles the heavy lifting of data retrieval and geometric comparison.

  1. Fetch zone data

    The agent gathers the logical shapes and coordinates for all active trigger zones.

    list_geofences

  2. Retrieve floor plans

    The AI pulls the structural layout and geometry for the specific site you are auditing.

    get_building

  3. Compare geometries

    The agent runs a check to see if the polygon coordinates sit within the valid building boundaries.

    list_geofencesget_building

  4. Flag discrepancies

    The AI identifies any zones that overlap with non-navigable areas or exit the building footprint.

    list_geofences

Try it

Copy these to start.

Use these prompts to kick off an audit.

Starting points

Replace the building names or zone IDs with your actual data.

Pointr Connector

You're all set. Choose your MCP client and follow the setup instructions.

Connector linkhttps://edge.vinkius.com/vk_preview_C80UHAWpnSofumPbQSlydWBY9PDBa9Vt5avQGQhi/mcp

Claude Desktop

Follow the steps below to connect in seconds.

  1. 1In Claude Desktop, open Settings → Connectors.
  2. 2Click “Add custom connector” and paste the connector link above as the remote MCP server URL.
  3. 3Click Add and start a new chat — Pointr capabilities are ready to use.
Configuration · claude_desktop_config.jsonCopy
{
  "mcpServers": {
    "pointr-mcp": {
      "url": "https://edge.vinkius.com/vk_preview_C80UHAWpnSofumPbQSlydWBY9PDBa9Vt5avQGQhi/mcp"
    }
  }
}
Copy into chat04

  • List all geofences in the North Warehouse and check if they fit the building layout.

  • Compare the coordinates of the 'Loading Dock' zone against the building geometry.

  • Are any of my geofences in the London Office overlapping with the structural walls?

  • Show me the polygon data for all zones in the Retail Plaza so I can verify them.

  • Claude
  • ChatGPT
  • Cursor
  • VS Code
  • Windsurf
  • Claude Code
  • JetBrains
  • Cline

Start here

Connect Pointr once, then ask.

One connection gives your agent access to your spatial data. Your credentials stay encrypted and secure.

Connect Pointr to your AI

FAQ

How this task behaves

  • 01

    Can the AI move my geofences for me?

    No. The AI can only read and analyze the data. You have to make any changes in your own system.

  • 02

    Does the AI see my real-time user locations?

    No. This specific task only accesses the logical polygons and building layouts.

  • 03

    Can I audit multiple buildings at once?

    Yes, as long as you specify the building names in your prompt.

  • 04

    Will the AI delete any zones?

    No. The tools provided are read-only for the purpose of verification.

  • 05

    How does it know where the walls are?

    It uses the building geometry retrieved through the building data tool.

  • More questions about Pointr? The Connector page answers them. See everything the Pointr Connector can do

Connect Pointr to Claude, Cursor, ChatGPT & more