• REBOOT
  • SHUTDOWN
  • STATUS
  • HUMAN

How to send remote node commands with your AI

Connect Shunwang Tech to your agent to manage hardware through chat. You'll issue power commands to specific nodes without using a terminal.

Ask AI about this page

Short answer

How can I send remote node commands with my AI?

Your agent uses the Shunwang Tech MCP to find your hardware and execute reboot or shutdown instructions. You get direct control over your nodes through your chat interface. Here is how it works.

Command outcomes

What your commands do

The results of your agent's actions.

REBOOT

System restarts

The agent triggers a reboot on the target node. This clears the local state and brings the hardware back online.

SHUTDOWN

Power off

The agent sends a shutdown command to the specific node you name. The hardware powers down completely.

STATUS

Node visibility

The agent identifies which nodes are currently reachable. You get a clear list of what's available to command.

HUMAN

Manual oversight

You decide which nodes receive commands. The AI won't execute a shutdown unless you explicitly tell it to.

The workflow

What your AI does when the command arrives.

The agent handles the technical handshake so you don't have to.

  1. Find nodes

    The agent looks up your hardware to find the right node for the job.

    list_nodes

  2. Confirm target

    The agent verifies the specific node you want to act on.

    list_nodes

  3. Send command

    The agent sends the actual reboot or shutdown signal to the hardware.

    send_node_command

  4. Verify action

    The agent confirms the instruction was successfully sent to the node.

    send_node_command

Try it

Copy these to start.

Use these prompts to trigger actions immediately.

Starting points

Swap out the node names or specific commands to match your actual hardware setup.

Shunwang Tech Connector

You're all set. Choose your MCP client and follow the setup instructions.

Connector linkhttps://edge.vinkius.com/vk_preview_bgiyuAWhRzWrIFnn1swCL5IcEpCA8FYUUwp4FNb7/mcp

Claude Desktop

Follow the steps below to connect in seconds.

  1. 1In Claude Desktop, open Settings → Connectors.
  2. 2Click “Add custom connector” and paste the connector link above as the remote MCP server URL.
  3. 3Click Add and start a new chat — Shunwang Tech capabilities are ready to use.
Configuration · claude_desktop_config.jsonCopy
{
  "mcpServers": {
    "shunwang-tech-mcp": {
      "url": "https://edge.vinkius.com/vk_preview_bgiyuAWhRzWrIFnn1swCL5IcEpCA8FYUUwp4FNb7/mcp"
    }
  }
}
Copy into chat04

  • List all my available nodes.

  • Reboot the node named production-server-01.

  • Shut down the node with ID 452.

  • Which nodes are currently online?

  • Claude
  • ChatGPT
  • Cursor
  • VS Code
  • Windsurf
  • Claude Code
  • JetBrains
  • Cline

Start here

Connect Shunwang Tech once, then ask.

Click the link to connect the MCP to your client. Your credentials stay encrypted and the setup is handled on our end.

Connect Shunwang Tech to your AI

FAQ

How the task behaves

  • 01

    Can the AI reboot nodes on its own?

    No. The AI only sends commands when you explicitly ask it to perform an action.

  • 02

    Can I use this to install new software?

    No. This MCP is limited to node management commands like reboot and shutdown.

  • 03

    Does the AI see my login credentials?

    No. Vinkius manages the connection securely so your agent only sees the tools.

  • 04

    How does the AI know which node to target?

    It uses the list of available nodes to match your request to a specific hardware ID.

  • 05

    Can the AI delete my data?

    No. There are no tools provided in this MCP for file deletion or data manipulation.

  • More questions about Shunwang Tech? The Connector page answers them. See everything the Shunwang Tech Connector can do

Connect Shunwang Tech to Claude, Cursor, ChatGPT & more