• DIMENSIONS
  • FLOW DATA
  • VALIDATION
  • HUMAN

How to size absorption columns with your AI

Connect this MCP to your AI client once. After that, you just provide the flow rates and fluid properties to get your dimensions.

Ask AI about this page

Short answer

How can I use AI to size an absorption column?

Your AI uses the gas and liquid flow rates you provide to calculate column diameter and height. You'll get the physical dimensions needed for your design. Here is the breakdown of the results you'll get.

The results you get

Design outputs

The AI handles the math and gives you these specific values.

DIMENSIONS

Column size specs

The AI calculates the required diameter and height. You get the physical constraints needed for the vessel design.

FLOW DATA

Flow rate analysis

The tool processes your gas and liquid flow rates. It ensures the sizing matches your specific throughput requirements.

VALIDATION

Design verification

The AI checks that the calculated dimensions meet the necessary absorption criteria. This confirms the column can handle the load.

HUMAN

Manual review needed

You must still verify these numbers against your specific safety standards and local engineering codes. The AI provides the math, but you own the final design.

The workflow

What your AI does when the data arrives.

The AI takes your raw process numbers and runs them through the sizing logic.

  1. Input processing

    Your AI reads the gas and liquid flow rates you provide in the chat. It organizes these into the necessary variables for the calculation.

    calculate_column_dimensions

  2. Dimension math

    The agent runs the sizing equations to find the diameter. It uses the flow rates to determine the minimum vessel width.

    calculate_column_dimensions

  3. Height determination

    The AI calculates the required height of the column. It accounts for the contact time needed for the absorption process.

    calculate_column_dimensions

  4. Final report

    The AI presents the diameter and height as a clear set of dimensions. You can then use these to start your equipment drawings.

    calculate_column_dimensions

Try it

Copy these to start.

Use these prompts to trigger the sizing calculations.

Starting points

Replace the bracketed values with your actual process data.

Absorption Column Design Connector

You're all set. Choose your MCP client and follow the setup instructions.

Connector linkhttps://edge.vinkius.com/vk_preview_6aahZKqO8YX7tDP6fGZVJyEE5fIJEz1DXqmb8aMn/mcp

Claude Desktop

Follow the steps below to connect in seconds.

  1. 1In Claude Desktop, open Settings → Connectors.
  2. 2Click “Add custom connector” and paste the connector link above as the remote MCP server URL.
  3. 3Click Add and start a new chat — Absorption Column Design capabilities are ready to use.
Configuration · claude_desktop_config.jsonCopy
{
  "mcpServers": {
    "absorption-column-design-mcp": {
      "url": "https://edge.vinkius.com/vk_preview_6aahZKqO8YX7tDP6fGZVJyEE5fIJEz1DXqmb8aMn/mcp"
    }
  }
}
Copy into chat04

  • Calculate the absorption column dimensions for a gas flow of 500 m3/h and a liquid flow of 20 m3/h.

  • Size an absorption column where the gas velocity is 0.5 m/s and the liquid rate is 15 m3/h.

  • What are the required diameter and height for a column with these specific flow rates: [insert rates]?

  • Run the sizing calculation for an absorption column using a gas flow of [X] and liquid flow of [Y].

  • Claude
  • ChatGPT
  • Cursor
  • VS Code
  • Windsurf
  • Claude Code
  • JetBrains
  • Cline

Start here

Connect Absorption Column Design once, then ask.

Just click the link to connect the MCP to your client. Your credentials stay encrypted, and you can start sizing columns immediately.

Connect Absorption Column Design to your AI

FAQ

How this task behaves

  • 01

    Can the AI design the internal trays or packing?

    No. The tool calculates the column diameter and height, but it does not design the internal hardware like trays or specific packing types.

  • 02

    Does the AI change my original flow rate data?

    No. The AI only reads the flow rates you provide to perform the math. It does not modify your source data.

  • 03

    Can I use this for any type of column?

    This specific tool is built for absorption columns. It won't work for stripping or distillation columns.

  • 04

    Will the AI automatically order the equipment?

    No. The AI only provides the calculated dimensions. You must handle all procurement and ordering yourself.

  • 05

    Does the AI handle fluid property lookups?

    No. You need to provide the specific gas and liquid flow rates for the calculation to work.

  • More questions about Absorption Column Design? The Connector page answers them. See everything the Absorption Column Design Connector can do

Connect Absorption Column Design to Claude, Cursor, ChatGPT & more