• AUDIT
  • VALIDATION
  • SUMMARY
  • HUMAN

How to inspect Make data stores with your AI

Connect your AI client to Make once. From then on, you can ask it to pull and check any data stored in your persistent Make data stores.

Ask AI about this page

Short answer

How can I check my Make data stores using AI?

Your AI client uses the list_data_stores tool to pull a list of your existing data stores. You can then ask it to verify specific entries or check for missing information. This gives you a direct way to audit your automation data.

The results of an inspection

Where your data insights land.

The AI handles the heavy lifting of data retrieval so you can focus on the results.

AUDIT

Data integrity checks

The AI pulls the current state of your data stores. You'll see exactly what was saved during your last automation run.

VALIDATION

Missing entry detection

Ask your agent to look for specific IDs or values. It identifies if a record failed to save or if a field is empty.

SUMMARY

Data store overviews

The AI lists all available data stores. This helps you keep track of your persistent storage across different scenarios.

HUMAN

Manual corrections

The AI only reads the data. If you find an error, you'll need to go into Make to fix the actual record.

The workflow

What your AI does when the request arrives.

The AI acts as a bridge between your chat interface and your Make storage.

  1. Identify stores

    The AI scans your Make account to find all active data stores available for inspection.

    list_data_stores

  2. Fetch contents

    Once you pick a store, the AI pulls the records to prepare them for your review.

    list_data_stores

  3. Analyze records

    Your agent compares the retrieved data against your specific requirements or expected values.

    list_data_stores

  4. Report findings

    The AI presents a clear summary of what it found, highlighting any discrepancies it spotted.

    list_data_stores

Try it

Copy these to start.

Use these prompts to begin your inspection.

Starting points

Swap out the bracketed text for your actual Make data store names or specific record IDs.

Make Connector

You're all set. Choose your MCP client and follow the setup instructions.

Connector linkhttps://edge.vinkius.com/vk_preview_r2CLvTcOALOF2OpiXX677eGYLrooDXLwGaSUPk6K/mcp

Claude Desktop

Follow the steps below to connect in seconds.

  1. 1In Claude Desktop, open Settings → Connectors.
  2. 2Click “Add custom connector” and paste the connector link above as the remote MCP server URL.
  3. 3Click Add and start a new chat — Make capabilities are ready to use.
Configuration · claude_desktop_config.jsonCopy
{
  "mcpServers": {
    "make-workflow-automation-mcp": {
      "url": "https://edge.vinkius.com/vk_preview_r2CLvTcOALOF2OpiXX677eGYLrooDXLwGaSUPk6K/mcp"
    }
  }
}
Copy into chat04

  • List all my Make data stores so I can see what's available.

  • Check the 'Customer Leads' data store and tell me if the last entry has an email address.

  • Look through my 'Inventory' data store and find any items with zero stock.

  • Summarize the most recent five entries in my 'Order Log' data store.

  • Claude
  • ChatGPT
  • Cursor
  • VS Code
  • Windsurf
  • Claude Code
  • JetBrains
  • Cline

Start here

Connect Make once, then ask.

You only need to link your Make account one time. Your credentials stay encrypted, and you can immediately start asking your AI to check your data.

Connect Make to your AI

FAQ

How this task behaves

  • 01

    Can the AI delete data from my Make data stores?

    No. This MCP only provides the ability to list and read data stores. It cannot delete or modify any records.

  • 02

    Can the AI add new rows to my data stores?

    No. The current tools only allow the AI to list and inspect existing data stores.

  • 03

    Does the AI see all my Make scenarios?

    The AI specifically accesses the data stores you authorize, not your entire scenario logic.

  • 04

    How does the AI know which data store to look at?

    You tell it which store to check by name, or it can list all available stores first so you can choose.

  • 05

    Can I use this with Claude or Cursor?

    Yes. Any MCP-compatible client like Claude, Cursor, or Windsurf can use this once you connect it via Vinkius.

  • More questions about Make? See everything the Make Connector can do

Connect Make to Claude, Cursor, ChatGPT & more