• VALID
  • OUTSIDE
  • MISSING
  • HUMAN

How to verify service areas with your AI

Connect MotionTools to your AI client to instantly cross-reference addresses against your operational boundaries.

Ask AI about this page

Short answer

Can my AI check if a location is in my service area?

Yes. Your AI uses the MotionTools MCP to pull your current service zones and compare them against any address you provide. You'll get an immediate confirmation of whether a pickup or dropoff is valid.

The outcomes.

Where your results land.

The AI processes your location requests and routes the outcome based on your service data.

VALID

In-zone confirmation

The AI identifies that the address matches your active territory. It confirms the location is ready for service.

OUTSIDE

Out-of-bounds alert

The AI flags that the requested location falls outside your defined service areas. It prevents you from scheduling impossible jobs.

MISSING

Missing zone data

If your service areas aren't set up, the AI will tell you it can't find any zones to check against.

HUMAN

Manual review needed

If an address is right on the edge of a zone, the AI flags it for you to make the final call.

The workflow

What your AI does when a location is provided.

The AI handles the heavy lifting of comparing coordinates and zone boundaries.

  1. Fetch active zones

    The AI pulls your full list of current service territories to establish a baseline.

    list_service_areas

  2. Identify specific zone

    The AI looks up the specific details for a single service area to check its boundaries.

    get_service_area

  3. Compare addresses

    The AI matches the provided pickup or dropoff address against the retrieved zone data.

    get_service_area

  4. Report status

    The AI gives you a clear yes or no regarding the location's eligibility.

    list_service_areas

Try it

Copy these to start.

Use these prompts to trigger the service area check.

Starting points

Swap the bracketed text for your actual business details.

MotionTools Connector

You're all set. Choose your MCP client and follow the setup instructions.

Connector linkhttps://edge.vinkius.com/vk_preview_6vafOiG0iEHs4dJrbsSA3LdFaQ3bcht1OjalMkTE/mcp

Claude Desktop

Follow the steps below to connect in seconds.

  1. 1In Claude Desktop, open Settings → Connectors.
  2. 2Click “Add custom connector” and paste the connector link above as the remote MCP server URL.
  3. 3Click Add and start a new chat — MotionTools capabilities are ready to use.
Configuration · claude_desktop_config.jsonCopy
{
  "mcpServers": {
    "motiontools-mcp": {
      "url": "https://edge.vinkius.com/vk_preview_6vafOiG0iEHs4dJrbsSA3LdFaQ3bcht1OjalMkTE/mcp"
    }
  }
}
Copy into chat04

  • Check if 123 Maple St is within my service areas.

  • List all my current service areas so I can see them.

  • Is the dropoff location at the downtown warehouse inside my active zone?

  • Verify if this pickup address in Springfield is covered by my service area.

  • Claude
  • ChatGPT
  • Cursor
  • VS Code
  • Windsurf
  • Claude Code
  • JetBrains
  • Cline

Start here

Connect MotionTools once, then ask.

Just link the MCP to your preferred client. Your credentials stay encrypted, and you can start asking questions immediately.

Connect MotionTools to your AI

FAQ

How this task behaves.

  • 01

    Can the AI add new service areas for me?

    No. The AI can only read and check existing areas using the available tools.

  • 02

    Will the AI automatically book a job if the area is valid?

    No. The AI only verifies the location. You must handle the actual booking yourself.

  • 03

    Does the AI know my exact GPS coordinates?

    The AI uses the address or location data you provide to check against your service zones.

  • 04

    Can I update my service zones through the chat?

    No. The AI does not have tools to modify or delete your service area settings.

  • 05

    What happens if I provide an invalid address?

    The AI will tell you it cannot verify the location against your service areas.

  • More questions about MotionTools? The Connector page answers them. See everything the MotionTools Connector can do

Connect MotionTools to Claude, Cursor, ChatGPT & more